Milestone XProtect Go 2014 Bedienungsanleitung Seite 90
- Seite / 220
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Milestone XProtect
®
Go 2014
Administrator's Manual
www.milestonesys.com
90
Advanced configuration
Start Event
Select required start event. The camera begins using the speedup
frame rates when the start event occurs.
Stop Event
Select required stop event. The camera returns to the normal frame
rates when the stop event occurs.
Properties available in XProtect Enterprise and XProtect Professional only:
Live Frame Rate
Required average frame rate for live video from the camera. Select
number of frames, then select the time unit interval (second, minute
or hour). The frame rate must be higher than the frame rate
specified under normal mode.
If the camera supports dual stream and dual stream is enabled, the
Live Frame Rate column will be read-only with the value Dual
streaming—which cannot be altered.
Recording Frame Rate
Required average frame rate for recorded video from the camera.
Select number of frames, then select the time unit interval (second,
minute or hour). The frame rate must be higher than the frame rate
specified under normal mode.
Note: Speedup does not necessarily have to be based on motion- or events, you can also use
scheduling to configure speedup based on particular periods of time. If you prefer such time-based
speedup, you should still enable the use of speedup by selecting the Enable speedup check box.
Dual stream
Enable dedicated live stream
This additional stream feature lets you use the alternative stream of
the camera. It enables two independent streams to the recording
server—a stream for live viewing and another stream for recording
purposes, with different resolution, encoding, and frame rate.
Stream
Select the type of the live stream. Stream settings for viewing live
video and for recording video may very well be different in order to
get the best result.
Resolution
Select the resolution of the camera.
FPS
Select the camera's live frame rate per second (FPS)
MPEG video format
With MPEG, you can define frame rate and other settings:
Frame rate
Properties available in all XProtect software versions:
Frame rate per second
Frame rate for viewing live and recorded video from the camera.
Select number of frames per second.
Properties available in XProtect Enterprise, XProtect Professional and XProtect Express only:
- Administrator's Manual 1
- Contents 2
- Before you start 10
- About administrator rights 11
- About daylight saving time 11
- About time servers 11
- About virus scanning 12
- System overview 13
- Differences in XProtect Go 14
- Clients 16
- Install silently 17
- Milestone Mobile client 18
- XProtect Web Client 20
- Recording Server Manager 21
- XProtect Download Manager 22
- Hiding and removing features 23
- Licenses 25
- About replacing cameras 26
- Install and upgrade 28
- Install video device drivers 30
- Upgrade 30
- First time use 34
- Best practices 35
- Power outages: use a UPS 36
- Print help topics 37
- About restarting services 38
- Monitor storage space usage 38
- Getting started 40
- Add hardware wizard 41
- Express 42
- Import from CSV file 44
- Configure storage wizard 45
- Manage user access wizard 56
- Advanced configuration 58
- Configure hardware devices 60
- Delete hardware devices 60
- Camera and database action 62
- Speaker properties 63
- Hardware properties 63
- PTZ device (properties) 64
- About database resizing 66
- About motion detection 66
- Enabled motion detection 67
- Disabled motion detection 67
- Motion detection sensitivity 67
- Online periods 68
- E-mail notification 69
- SMS notification 69
- Set up a profile 69
- Configure motion detection 70
- Disable or delete cameras 70
- Video recording (properties) 74
- Regular frame rate mode: 77
- Speedup frame rate mode: 78
- Dual stream: 79
- Manual recording 80
- Frame rate - MJPEG 81
- Frame Rate - MPEG 84
- Audio recording 85
- Audio selection 86
- Camera properties 87
- MJPEG video format 89
- Regular frame rate mode 89
- Speedup frame rate mode 89
- Dual stream 90
- MPEG video format 90
- Frame rate 90
- Recording 92
- Event notification 96
- Privacy masking 99
- 360° lens 100
- Fisheye 101
- PTZ preset positions 102
- PTZ patrolling 104
- Patrolling list 105
- PTZ scanning 105
- PTZ on event 106
- Microphones 107
- Microphone (properties) 108
- Events and output 109
- Add an analytics event 111
- Add a hardware input event 111
- Add a hardware output 112
- Add a manual event 113
- Add a generic event 113
- Add a timer event 114
- Test a generic event 115
- General event properties 117
- Events and output properties 118
- Hardware input event 119
- Hardware output 121
- Manual event 121
- Timer event 122
- Generic event 123
- (indicated in red) 124
- Scheduling and archiving 126
- About archiving 127
- About archiving locations 128
- About archiving audio 129
- About archiving schedules 130
- Scheduling all cameras 132
- Scheduling options 134
- Archiving 134
- Online period 135
- Speedup 136
- About Matrix video sharing 137
- About Matrix-recipients 137
- Configure Matrix 138
- Matrix properties 138
- Matrix event control 139
- About logs 140
- Log locations 141
- Log structures 142
- Log integrity checks 142
- Log properties 143
- Audit Log 144
- Notifications 145
- Attachment Settings (email) 146
- Server Settings (email) 147
- About SMS 148
- Configure SMS notifications 148
- SMS properties 148
- Server Settings (SMS) 149
- Scheduling 150
- Central 151
- Access control 152
- Steps in this wizard: 153
- Associated cameras 153
- Final summary 153
- Access control properties 154
- Access Control Actions 156
- Server access 159
- Configure server access 160
- Server access properties 160
- Local IP ranges 161
- Master/Slave 162
- Slave server properties 163
- Update status on slaves 163
- About users 164
- Add basic users 164
- Add Windows users 164
- Add user groups 165
- User properties 166
- General access 167
- Camera access 167
- Services 169
- Start and stop services 170
- Servers 171
- Mobile server settings 174
- Server Status 175
- Video Push 176
- Exported recordings 177
- Performance 178
- Mobile Server Manager 179
- About show status 180
- Edit certificate 181
- About alarms 182
- Time profiles for alarms 183
- Alarms and XProtect Central 183
- Viewing alarms 183
- About maps 184
- Add an alarm 184
- Alarms properties 185
- Alarm data settings 187
- Sound settings 188
- Time profile 188
- MIP plug-ins 189
- Settings 190
- Options 191
- User Interface 192
- Default File Paths 193
- Analytics Event Settings 193
- Event Server Settings 194
- System maintenance 196
- Restore system configuration 197
- Glossary of Terms 203
Verwandte Produkte und Handbücher für Software Milestone XProtect Go 2014
Software Milestone M50 Bedienungsanleitung
(215 Seiten)
(215 Seiten)
Software Milestone M10 Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Software Milestone LPR 1.0 Bedienungsanleitung
(47 Seiten)
(47 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern