Milestone XProtect Go 2014 Bedienungsanleitung Seite 63
- Seite / 220
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Milestone XProtect
®
Go 2014
Administrator's Manual
www.milestonesys.com
63
Advanced configuration
Speaker properties
When you configure video and recording (see "About video and recording configuration" on page 65)
for specific cameras, you can determine when to record audio. Your choice applies for all cameras on
your system.
Name
Description
Enabled
Speakers are by default enabled, meaning they can transfer audio
to your system. If required, you can disable an individual speaker, in
which case no audio is transferred from the speaker to the system.
Speaker name
The name as it appears in the Management Application as well as
in clients. You can overwrite the existing name with a new one.
Names must be unique, and must not contain any of these special
characters: < > & ' " \ / : * ? | [ ]
Hardware properties
Hardware name and video channels
When you configure hardware devices, specify the following properties:
Name
Description
Hardware name
The name as it appears in the Management Application as well as
in clients. You can overwrite the existing name with a new one.
Names must be unique, and must not contain any of these special
characters: < > & ' " \ / : * ? | [ ]
Video channel # enabled
Enable/disable each of the selected hardware device's video
channels. Many hardware devices only have a single video
channel, in which case only one channel will be listed. Other
hardware devices—typically video encoder devices—have several
video channels.
If some of the channels are unavailable, this is because you are not licensed to use all of a video
encoder device's channels.
Example: You have a video encoder device with four channels, but your license for the device only
allows you to use two of them. In that case, you can only have two channels enabled at a time, while
the two other channels are disabled. Note that you are free to select which two channels you want to
enable. Contact your Milestone vendor if you need to change your number of licenses.
Network, device type, and license
When you configure hardware devices (on page 60), specify the following properties:
Name
Description
IP Address
IP address or host name of the hardware device.
- Administrator's Manual 1
- Contents 2
- Before you start 10
- About administrator rights 11
- About daylight saving time 11
- About time servers 11
- About virus scanning 12
- System overview 13
- Differences in XProtect Go 14
- Clients 16
- Install silently 17
- Milestone Mobile client 18
- XProtect Web Client 20
- Recording Server Manager 21
- XProtect Download Manager 22
- Hiding and removing features 23
- Licenses 25
- About replacing cameras 26
- Install and upgrade 28
- Install video device drivers 30
- Upgrade 30
- First time use 34
- Best practices 35
- Power outages: use a UPS 36
- Print help topics 37
- About restarting services 38
- Monitor storage space usage 38
- Getting started 40
- Add hardware wizard 41
- Express 42
- Import from CSV file 44
- Configure storage wizard 45
- Manage user access wizard 56
- Advanced configuration 58
- Configure hardware devices 60
- Delete hardware devices 60
- Camera and database action 62
- Speaker properties 63
- Hardware properties 63
- PTZ device (properties) 64
- About database resizing 66
- About motion detection 66
- Enabled motion detection 67
- Disabled motion detection 67
- Motion detection sensitivity 67
- Online periods 68
- E-mail notification 69
- SMS notification 69
- Set up a profile 69
- Configure motion detection 70
- Disable or delete cameras 70
- Video recording (properties) 74
- Regular frame rate mode: 77
- Speedup frame rate mode: 78
- Dual stream: 79
- Manual recording 80
- Frame rate - MJPEG 81
- Frame Rate - MPEG 84
- Audio recording 85
- Audio selection 86
- Camera properties 87
- MJPEG video format 89
- Regular frame rate mode 89
- Speedup frame rate mode 89
- Dual stream 90
- MPEG video format 90
- Frame rate 90
- Recording 92
- Event notification 96
- Privacy masking 99
- 360° lens 100
- Fisheye 101
- PTZ preset positions 102
- PTZ patrolling 104
- Patrolling list 105
- PTZ scanning 105
- PTZ on event 106
- Microphones 107
- Microphone (properties) 108
- Events and output 109
- Add an analytics event 111
- Add a hardware input event 111
- Add a hardware output 112
- Add a manual event 113
- Add a generic event 113
- Add a timer event 114
- Test a generic event 115
- General event properties 117
- Events and output properties 118
- Hardware input event 119
- Hardware output 121
- Manual event 121
- Timer event 122
- Generic event 123
- (indicated in red) 124
- Scheduling and archiving 126
- About archiving 127
- About archiving locations 128
- About archiving audio 129
- About archiving schedules 130
- Scheduling all cameras 132
- Scheduling options 134
- Archiving 134
- Online period 135
- Speedup 136
- About Matrix video sharing 137
- About Matrix-recipients 137
- Configure Matrix 138
- Matrix properties 138
- Matrix event control 139
- About logs 140
- Log locations 141
- Log structures 142
- Log integrity checks 142
- Log properties 143
- Audit Log 144
- Notifications 145
- Attachment Settings (email) 146
- Server Settings (email) 147
- About SMS 148
- Configure SMS notifications 148
- SMS properties 148
- Server Settings (SMS) 149
- Scheduling 150
- Central 151
- Access control 152
- Steps in this wizard: 153
- Associated cameras 153
- Final summary 153
- Access control properties 154
- Access Control Actions 156
- Server access 159
- Configure server access 160
- Server access properties 160
- Local IP ranges 161
- Master/Slave 162
- Slave server properties 163
- Update status on slaves 163
- About users 164
- Add basic users 164
- Add Windows users 164
- Add user groups 165
- User properties 166
- General access 167
- Camera access 167
- Services 169
- Start and stop services 170
- Servers 171
- Mobile server settings 174
- Server Status 175
- Video Push 176
- Exported recordings 177
- Performance 178
- Mobile Server Manager 179
- About show status 180
- Edit certificate 181
- About alarms 182
- Time profiles for alarms 183
- Alarms and XProtect Central 183
- Viewing alarms 183
- About maps 184
- Add an alarm 184
- Alarms properties 185
- Alarm data settings 187
- Sound settings 188
- Time profile 188
- MIP plug-ins 189
- Settings 190
- Options 191
- User Interface 192
- Default File Paths 193
- Analytics Event Settings 193
- Event Server Settings 194
- System maintenance 196
- Restore system configuration 197
- Glossary of Terms 203
Verwandte Produkte und Handbücher für Software Milestone XProtect Go 2014
Software Milestone M50 Bedienungsanleitung
(215 Seiten)
(215 Seiten)
Software Milestone M10 Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Software Milestone LPR 1.0 Bedienungsanleitung
(47 Seiten)
(47 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern